Sentinel Zero Voc Lead Encapsulant, Clear or White 5 gal Pails

SENTINEL LEAD ENCAPSULANT is an Interior/ Exterior, water based, Zero V.O.C., low odor coating designed as
a permanent solution for abatement of lead- based paint. Sentinel Lead Encapsulant is formulated with a
flexible, durable, high solids finish to provide a thick barrier that traps and holds in lead contaminants on a
variety of building surfaces. Sentinel Lead Encapsulant contains a bitter tasting anti-ingestant which deters
children from oral contact. Sentinel Lead Encapsulant has been tested independently and found to meet the
ASTM E-1795 requirements for liquid coating lead encapsulation products. Sentinel Lead Encapsulant complies
with HUD & EPA for abatement by encapsulation.

Warning: Removal of old paint by sanding, scraping or other means may generate dust or fumes which contain
lead. Exposure to lead dust or fumes may cause adverse health effects especially in children or pregnant women.
Controlling exposure to lead or other hazardous substances requires the use of a properly fitted respirator (NIOSH
approved) with proper containment and clean up. For additional information, contact the USEPA/LEAD
information hotline at 1-800-424-LEAD (5323) or visit the EPA’s website at www.EPA.GOV/LEAD. This product
complies with Federal law restricting the presence of lead in consumer coatings. Contact Federal, State and Local
agencies for regulations regarding approved applicators, products and procedures. Determine the suitability of
using Sentinel Lead Encapsulant on all building surfaces included in the applicable areas. Note: Some states
require a surface assessment by a licensed lead inspector which may include a patch test for adhesion of the
paint coats. Not for use on friction surfaces or movable building components. Refer to the product Safety Data
Sheet for further information on personal protection equipment (PPE). Protect Sentinel Lead Encapsulant from
freezing. Store product in a dry place at temperatures between 40°F- 90°F. Use adequate ventilation during
application. Avoid contact with eyes and skin. Wash hands and all skin contact areas after use.

Material Preparation: Thoroughly stir and mix coating to achieve an even consistency for spraying, brushing or
rolling. Product must NOT be reduced with water or solvents. This product must not be allowed to freeze. Apply in temperatures above 45˚ F.

Characteristics: Pounds Per Gallon: 11.45
Percent of Solids/weight: 55.4%
Percent of Solids/Volume: 38.8%
Viscosity,KU: 110-120
Specular Gloss @ 60˚: 2
Flash Point: : None to boiling
Shelf Life: Unopened Container 2 Years
VOC Content: <5 g/L

Surface Preparation: Before applying Sentinel Lead Encapsulant, make sure all surfaces are dry, clean and free
of loose contaminants. For glossy surfaces deglossing is required. Wash oily or soiled surfaces, rinse and allow to
dry before applying the coating.

Surface Priming: Prime unpainted wood, drywall, brick and masonry surfaces with Lockdown Sealant. Unpainted metal surfaces should be treated with a rust inhibitive primer.

Tinting: This product may be tinted with universal colorant systems. Colorant loading to a maximum of 2 oz. per gallon.

Product Application: Apply Sentinel Lead Encapsulant at temps above 45º F. for at least 6 hours during and
after application to ensure a properly cured coating. Sentinel Lead Encapsulant requires a 10-14 wet mils thickness which should be applied in 2 or more coats. Use a wet mil gauge to measure the coating thickness. Apply
Sentinel Lead Encapsulant with a brush, roller or an airless sprayer with a .019-.021 spray tip.
Dry Time: Sentinel Lead Encapsulant will be dry to the touch after 2 hours and can be recoated after 4 hours.
Coverage: 165 sq. ft per gallon applied at 10 wet mils.

Warranty: Sentinel Products Inc. warrants this product to perform satisfactorily for 20 years from the
date that the product is applied when used in accordance with the label directions. Sentinel Products Inc. will replace the product or refund the purchase price in the event this product is proven defective, which shall be the
exclusive remedy under the warranty. Liability for consequential damages is specifically excluded. No other warranties expressed or implied are given.

Notice: A zero V.O.C. coating by industry standards means the product contains fewer than 5 grams of V.O.C.’s per liter. Tints and colorants may add V.O.C.’s to the product.

Product Data Sheet-White                   Product Data Sheet-Clear

Safety Data Sheet-White                      Safety Data Sheet-Clear

$299.95